Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
This great article listed below in relation to Installing A Bathtub is relatively informative. Read it yourself and figure out what you think about it.
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably challenging task. If the old tub is readily available, the project can move speedily; if you have to open a wall surface to eliminate the old tub as well as place the brand-new bath tub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will require a helper to vacate the old tub and also set in the new one. Ensure you have actually certified on your own for the work and also are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to consider using one before you start. Possibilities are you might require a professional plumber to make tube links.
This post will certainly assist you set up a brand-new bathtub in your washroom if you have actually already gotten a brand-new bathtub as well as don't need to transform the arrangement of your previous water system pipelines.
Your devices as well as product checklist should make up the following:
Preparing for the Installment
First of all, the supporting framework provided with the bath should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited gain access to that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wood boards under its feet, put the bath tub in the called for position. The wood boards are helpful in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the tub till the level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water supply and check all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub as well as additionally check the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bathtub has been used a minimum of once as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in area in between the faucet and the sink. Safeguard the faucet in position with the maker offered backnut. When the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall between the bath and the tiling, bring about issues with wetness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in use. The sealant can break relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the marketplace. It is recommended to fit the tiles using waterproof or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very drawn to Installing A Bathtub and I hope you appreciated the entire blog post. Liked our review? Please share it. Help another person discover it. I enjoy reading our article about How to Install a Bathtub.
Ensure plumbing safety. Report this page